Balmar XT-Series 170A 12V Marine Alternator, K6 or J10 Pulley
- 170A from a small case
- Up to 128A at idle
- Smart Ready backup
- Single or dual foot
- Output 170A, 12V
- Idle Up to 128A
- Stator Braided Wire
- Warranty 2-Year Limited
Get big-alternator charging from a small-case package with the Balmar XT-Series 170A Alternator. Its advanced braided wire stator delivers up to 128 amps at idle and 170 amps at speed, enough to keep large house banks, lithium batteries and heavy electrical loads charged even on short engine runs. Dual internal fans and a high-airflow frame keep it cool, and Balmar's patented Smart Ready regulator provides built-in backup regulation. This is the alternator only; pair it with a Balmar Max Charge MC-618 regulator for full multi-stage charging.
- Output: 170A, Up to 128A at Idle
- Stator: Braided Wire, 96 Slots
- Cooling: Dual Internal Fans
- Mounts: 1-2" Single Foot or 3.15" Dual Foot
Braided Stator Technology
XT-Series alternators use a braided wire stator with about 85% copper winding density, compared with roughly 70% for hairpin stators and 45% for traditional S-wound stators. That density makes the alternator more efficient, delivering more power at low RPM, more total output and cooler running. The XT-Series runs 5 to 10°C cooler than Balmar's earlier AT-Series alternators.
Power at Idle
With up to 128A available at idle, the XT-170 puts real current back into your batteries while you motor slowly, maneuver in a marina or run the engine at anchor, cutting the run time needed to recharge.
Smart Ready Regulation
Balmar's patented Smart Ready internal regulator holds 14.1 volts if the external regulator is ever disconnected or fails, giving you a built-in get-home backup. For full multi-stage charging of a large house bank, the alternator is controlled by an external Balmar Max Charge MC-618 regulator.
Built for Hard Duty
Sealed heavy-duty bearings, 50A-rated diodes, a ventilated cast aluminum case and red powder-coat finish stand up to marine conditions. The XT-Series is certified to USCG Title 33, SAE J1171, CE and ISO 8846 ignition protection standards.
Choose Your Mount and Pulley
- Single Foot, J10 Pulley (XT-SF-170-J10): 1" or 2" spindle mount with a 10-groove serpentine pulley
- Single Foot, K6 Pulley (XT-SF-170-K6): 1" or 2" spindle mount with a 6-groove serpentine pulley
- Dual Foot 3.15", K6 Pulley (XT-DF-170-K6): Hitachi-style saddle mount, typical for Yanmar, Westerbeke, Lehman and Perkins-Sabre engines
Installation Notes
- This alternator requires an external Balmar MC-618 regulator for multi-stage charging (sold separately); the XT-Series kits include it
- XT-Series alternators should only be used with dual vee or multi-groove serpentine belts; if your engine uses a single vee belt, a Balmar AltMount pulley conversion kit is required
- If your tachometer reads from the alternator and is not adjustable, you may need Balmar's Tachometer Signal Stabilizer (15-TSS)
- XT-Series alternators are case ground
- Upgrade charging cables and fusing to suit the higher output before installation
What’s Included
- 1 x Balmar XT-Series 170A 12V alternator (mount and pulley per selection)
- Regulator, temperature sensors and mounting hardware are not included
| Brand | Balmar |
| Part Numbers | XT-SF-170-J10, XT-SF-170-K6, XT-DF-170-K6 |
| Series | XT-Series |
| Rated Output | 170A |
| Idle Output | Up to 128A |
| Voltage | 12V |
| Mounting | 1-2" Single Foot Spindle or 3.15" Dual Foot Saddle |
| Pulley OD | K6: 2.42" (61 mm) / J10: 2.28" (57 mm) |
| Power Take-Off | 5.2 HP |
| Cut-In Speed | 1,150 Alternator RPM |
| Max Alternator Speed | 18,000 RPM |
| Stator | Braided Wire, 16 Poles, 96 Slots |
| Diodes | 6 Positive / 6 Negative, 50A Rated |
| Field Type | P-Type, Positive Field Excitation |
| Internal Regulation | Smart Ready, 14.1V |
| External Regulator | Balmar MC-618 (Sold Separately) |
| Output Stud | M8 x 1.25 |
| Grounding | Case Ground |
| Bearings | Sealed Heavy-Duty Radial |
| Certifications | USCG Title 33, SAE J1171, CE, ISO 8846 |
| Shipping Weight | 13.9-14.5 lb |
| UPC | SF-J10: 676205500838 / SF-K6: 676205500852 / DF-K6: 676205500791 |
| Warranty | 2-Year Limited |
| Brand | Balmar |
| Part Numbers | XT-SF-170-J10, XT-SF-170-K6, XT-DF-170-K6 |
| Series | XT-Series |
| Rated Output | 170A |
| Idle Output | Up to 128A |
| Voltage | 12V |
| Mounting | 1-2" Single Foot Spindle or 3.15" Dual Foot Saddle |
| Pulley OD | K6: 2.42" (61 mm) / J10: 2.28" (57 mm) |
| Power Take-Off | 5.2 HP |
| Cut-In Speed | 1,150 Alternator RPM |
| Max Alternator Speed | 18,000 RPM |
| Stator | Braided Wire, 16 Poles, 96 Slots |
| Diodes | 6 Positive / 6 Negative, 50A Rated |
| Field Type | P-Type, Positive Field Excitation |
| Internal Regulation | Smart Ready, 14.1V |
| External Regulator | Balmar MC-618 (Sold Separately) |
| Output Stud | M8 x 1.25 |
| Grounding | Case Ground |
| Bearings | Sealed Heavy-Duty Radial |
| Certifications | USCG Title 33, SAE J1171, CE, ISO 8846 |
| Shipping Weight | 13.9-14.5 lb |
| UPC | SF-J10: 676205500838 / SF-K6: 676205500852 / DF-K6: 676205500791 |
| Warranty | 2-Year Limited |