Balmar XT-Series 170A Marine Alternator Kit with MC-618 Regulator
- Complete 170A charging kit
- MC-618 smart regulator
- Lithium-ready programming
- Up to 128A at idle
- Output 170A, 12V
- Regulator MC-618
- Lithium LiFePO4 Program
- Warranty 2-Year Limited
Everything you need to transform your boat's charging system comes in the Balmar XT-Series 170A Alternator Kit. It pairs the XT-170 alternator, with its braided stator and up to 128 amps at idle, with Balmar's Max Charge MC-618 smart regulator, alternator and battery temperature sensors and mounting hardware. It's well suited to large AGM and lithium house banks, refrigeration, watermakers and inverters, putting more amps back into the batteries in less engine time.
- Output: 170A, Up to 128A at Idle
- Regulator: Max Charge MC-618, Multi-Stage
- Batteries: Flooded, AGM, Gel, LiFePO4 & More
- Mounts: 1-2" Single Foot or 3.15" Dual Foot
Braided Stator Technology
XT-Series alternators use a braided wire stator with about 85% copper winding density, compared with roughly 70% for hairpin stators and 45% for traditional S-wound stators. That density makes the alternator more efficient, delivering more power at low RPM, more total output and cooler running. The XT-Series runs 5 to 10°C cooler than Balmar's earlier AT-Series alternators.
Smart, Multi-Stage Charging
The included Balmar Max Charge MC-618 is a smart, multi-stage regulator with presets for flooded, AGM, gel, carbon foam, spiral-wound and LiFePO4 lithium batteries. Its included alternator and battery temperature sensors let it reduce output if the alternator runs hot and adjust charging voltage for battery temperature, and its Belt Load Manager and Small Engine Mode let you limit alternator load on smaller engines.
Lithium Ready
The MC-618's LiFePO4 program, combined with the alternator temperature sensor, makes this kit a strong match for lithium house banks, where an unregulated alternator can overheat. A battery management system is still required for lithium batteries.
Smart Ready Backup Regulation
Balmar's patented Smart Ready internal regulator holds 14.1 volts if the external regulator is ever disconnected or fails, giving you a built-in get-home backup.
Choose Your Mount and Pulley
- Single Foot, Dual Vee Pulley (XT-SF-170-DV-KIT): 1" or 2" spindle mount with a deep dual vee pulley
- Single Foot, K6 Pulley (XT-SF-170-K6-KIT): 1" or 2" spindle mount with a 6-groove serpentine pulley
- Dual Foot 3.15", K6 Pulley (XT-CR-170-K6-KIT): 3.15" saddle mount in Balmar's CR design, provided for Yanmar common rail engines
Installation Notes
- XT-Series alternators should only be used with dual vee or multi-groove serpentine belts; if your engine uses a single vee belt, a Balmar AltMount pulley conversion kit is required
- If your tachometer reads from the alternator and is not adjustable, you may need Balmar's Tachometer Signal Stabilizer (15-TSS)
- XT-Series alternators are case ground
- Upgrade charging cables and fusing to suit the higher output before installation
- Mount the MC-618 regulator in a dry location away from direct engine heat
- Professional installation is recommended; Balmar warranty coverage requires installation by a qualified installer
What’s Included
- 1 x Balmar XT-Series 170A 12V alternator (mount and pulley per selection)
- 1 x Balmar Max Charge MC-618 voltage regulator with wiring harness
- Alternator (MC-TS-A) and battery (MC-TS-B) temperature sensors
- Mounting hardware
| Brand | Balmar |
| Part Numbers | XT-SF-170-DV-KIT, XT-SF-170-K6-KIT, XT-CR-170-K6-KIT |
| Series | XT-Series |
| Rated Output | 170A |
| Idle Output | Up to 128A |
| Voltage | 12V |
| Mounting | 1-2" Single Foot Spindle or 3.15" Dual Foot Saddle (CR) |
| Pulley OD | K6: 2.42" (61 mm) / Dual Vee: 2.71" (68 mm) |
| Power Take-Off | 5.2 HP |
| Stator | Braided Wire, 16 Poles, 96 Slots |
| Internal Regulation | Smart Ready, 14.1V Backup |
| Regulator | Max Charge MC-618 with Harness |
| Battery Programs | Flooded, Deep Cycle, AGM, Gel, Carbon Foam, Spiral Wound, LiFePO4 |
| Temperature Sensors | MC-TS-A Alternator, MC-TS-B Battery |
| Output Stud | M8 x 1.25 |
| Grounding | Case Ground |
| Certifications | USCG Title 33, SAE J1171, CE, ISO 8846 |
| Kit Shipping Weight | 17.5-18 lb |
| UPC | SF-DV: 676205500821 / SF-K6: 676205500869 / CR-K6: 676205503594 |
| Warranty | 2-Year Limited |
| Brand | Balmar |
| Part Numbers | XT-SF-170-DV-KIT, XT-SF-170-K6-KIT, XT-CR-170-K6-KIT |
| Series | XT-Series |
| Rated Output | 170A |
| Idle Output | Up to 128A |
| Voltage | 12V |
| Mounting | 1-2" Single Foot Spindle or 3.15" Dual Foot Saddle (CR) |
| Pulley OD | K6: 2.42" (61 mm) / Dual Vee: 2.71" (68 mm) |
| Power Take-Off | 5.2 HP |
| Stator | Braided Wire, 16 Poles, 96 Slots |
| Internal Regulation | Smart Ready, 14.1V Backup |
| Regulator | Max Charge MC-618 with Harness |
| Battery Programs | Flooded, Deep Cycle, AGM, Gel, Carbon Foam, Spiral Wound, LiFePO4 |
| Temperature Sensors | MC-TS-A Alternator, MC-TS-B Battery |
| Output Stud | M8 x 1.25 |
| Grounding | Case Ground |
| Certifications | USCG Title 33, SAE J1171, CE, ISO 8846 |
| Kit Shipping Weight | 17.5-18 lb |
| UPC | SF-DV: 676205500821 / SF-K6: 676205500869 / CR-K6: 676205503594 |
| Warranty | 2-Year Limited |