Balmar XT-Series 250A Marine Alternator Kit with MC-618 Regulator, K6 or Dual Vee
- Complete 250A charging kit
- MC-618 smart regulator
- Up to 186A at idle
- Lithium-ready programming
- Output 250A, 12V
- Regulator MC-618
- Lithium LiFePO4 Program
- Warranty 2-Year Limited
The Balmar XT-Series 250A Alternator Kit is a complete high-output charging system for serious cruising boats. It combines the XT-250 alternator, which produces up to 186 amps at idle, with Balmar's Max Charge MC-618 smart regulator, alternator and battery temperature sensors and mounting hardware. Paired with a large AGM or lithium house bank, it delivers the charging power needed for inverters, air conditioning, watermakers and all-electric galleys while keeping engine run time to a minimum.
- Output: 250A, Up to 186A at Idle
- Regulator: Max Charge MC-618, Multi-Stage
- Batteries: Flooded, AGM, Gel, LiFePO4 & More
- Mounts: 3.15" or 4" Dual Foot
250 Amps in a Small Case
The XT-250 delivers large-frame output from Balmar's compact XT-Series case with a braided wire stator, dual internal fans and sealed heavy-duty bearings. The XT-Series runs 5 to 10°C cooler than Balmar's earlier AT-Series alternators.
Smart, Multi-Stage Charging
The included Balmar Max Charge MC-618 is a smart, multi-stage regulator with presets for flooded, AGM, gel, carbon foam, spiral-wound and LiFePO4 lithium batteries. Its included alternator and battery temperature sensors let it reduce output if the alternator runs hot and adjust charging voltage for battery temperature, and its Belt Load Manager and Small Engine Mode let you limit alternator load on smaller engines.
Lithium Ready
The MC-618's LiFePO4 program and alternator temperature sensor protect the XT-250 when charging lithium banks, which accept current fast enough to overheat an unregulated alternator. A battery management system is still required.
Smart Ready Backup Regulation
Balmar's patented Smart Ready internal regulator holds 14.1 volts if the external regulator is ever disconnected or fails, giving you a built-in get-home backup.
Choose Your Mount and Pulley
- Dual Foot 3.15", K6 Pulley (XT-CR-250-K6-KIT): 3.15" saddle mount in Balmar's CR design, provided for Yanmar common rail engines
- Dual Foot 4", Dual Vee Pulley (XT-DF4-250-DV-KIT): 4" J-180-style saddle mount, typical for Caterpillar, Cummins, Detroit Diesel and John Deere engines
Installation Notes
- At 6.6 HP of power take-off, confirm your engine and belt drive can handle a 250A alternator
- XT-Series alternators should only be used with dual vee or multi-groove serpentine belts; if your engine uses a single vee belt, a Balmar AltMount pulley conversion kit is required
- If your tachometer reads from the alternator and is not adjustable, you may need Balmar's Tachometer Signal Stabilizer (15-TSS)
- XT-Series alternators are case ground
- Upgrade charging cables and fusing to suit the higher output before installation
- Mount the MC-618 regulator in a dry location away from direct engine heat
- Professional installation is recommended; Balmar warranty coverage requires installation by a qualified installer
What’s Included
- 1 x Balmar XT-Series 250A 12V alternator (mount and pulley per selection)
- 1 x Balmar Max Charge MC-618 voltage regulator with wiring harness
- Alternator (MC-TS-A) and battery (MC-TS-B) temperature sensors
- Mounting hardware
| Brand | Balmar |
| Part Numbers | XT-CR-250-K6-KIT, XT-DF4-250-DV-KIT |
| Series | XT-Series |
| Rated Output | 250A |
| Idle Output | Up to 186A |
| Voltage | 12V |
| Mounting | 3.15" Dual Foot Saddle (CR) or 4" Dual Foot Saddle (J-180 Style) |
| Pulley | K6 Serpentine or Dual Vee |
| Power Take-Off | 6.6 HP |
| Stator | Braided Wire, 16 Poles, 96 Slots |
| Internal Regulation | Smart Ready, 14.1V Backup |
| Regulator | Max Charge MC-618 with Harness |
| Battery Programs | Flooded, Deep Cycle, AGM, Gel, Carbon Foam, Spiral Wound, LiFePO4 |
| Temperature Sensors | MC-TS-A Alternator, MC-TS-B Battery |
| Output Stud | M8 x 1.25 |
| Grounding | Case Ground |
| Certifications | USCG Title 33, SAE J1171, CE, ISO 8846 |
| Kit Shipping Weight | 20.5-21 lb |
| Replaces | DF4: AT-DF4-MC-200-KIT |
| UPC | CR-K6: 676205503518 / DF4-DV: 676205502801 |
| Warranty | 2-Year Limited |
| Brand | Balmar |
| Part Numbers | XT-CR-250-K6-KIT, XT-DF4-250-DV-KIT |
| Series | XT-Series |
| Rated Output | 250A |
| Idle Output | Up to 186A |
| Voltage | 12V |
| Mounting | 3.15" Dual Foot Saddle (CR) or 4" Dual Foot Saddle (J-180 Style) |
| Pulley | K6 Serpentine or Dual Vee |
| Power Take-Off | 6.6 HP |
| Stator | Braided Wire, 16 Poles, 96 Slots |
| Internal Regulation | Smart Ready, 14.1V Backup |
| Regulator | Max Charge MC-618 with Harness |
| Battery Programs | Flooded, Deep Cycle, AGM, Gel, Carbon Foam, Spiral Wound, LiFePO4 |
| Temperature Sensors | MC-TS-A Alternator, MC-TS-B Battery |
| Output Stud | M8 x 1.25 |
| Grounding | Case Ground |
| Certifications | USCG Title 33, SAE J1171, CE, ISO 8846 |
| Kit Shipping Weight | 20.5-21 lb |
| Replaces | DF4: AT-DF4-MC-200-KIT |
| UPC | CR-K6: 676205503518 / DF4-DV: 676205502801 |
| Warranty | 2-Year Limited |