Scotty 1106 Depthpower Electric Downrigger, 60" Telescoping Boom, Rod Holder & Swivel Base
- 235 ft/min retrieval on just 4 amps
- 36"–60" telescoping stainless boom
- 250 ft of 150 lb stainless cable
- Hands-free auto-stop at any depth
- Retrieval 235 ft/min with a 7 lb weight
- Boom 36"-60" Telescoping Stainless
- Cable 250 ft of 150 lb Stainless
- Amp Draw As Low as 4 A
When the fish are holding at 60 feet, you need your bait at 60 feet, not somewhere near it. The Scotty 1106 Depthpower is Scotty’s most popular electric downrigger because it gets your spread to an exact depth, brings the weight home fast at the flip of a switch, and barely touches your battery while it does it.
A 36”–60” telescoping stainless boom reaches past the motor and out wide for a clean multi-line spread, then collapses for docking and trailering. The 1106 arrives fully assembled and factory tested with 250 ft of 150 lb stainless cable, a Rod Master II rod holder, a 16-position swivel base and a tilt-up bracket, ready to bolt on and fish.
- Retrieval: 235 ft/min with a 7 lb weight
- Boom: 36”–60” Telescoping Stainless
- Cable: 250 ft of 150 lb Stainless
- Amp Draw: As Low as 4 A
Fast Retrieval That Sips Power
Scotty’s positive-drive belt system turns the spool more efficiently than worm-gear drives, so the 1106 resets your gear quickly without draining the battery that runs your electronics. Scotty rates it as having the lowest amperage draw of any downrigger, using less than one-third the battery power of some competitors. Scotty’s rated performance:
- 7 lb weight: 235 ft/min at 4 amps
- 10 lb weight: 222 ft/min at 5 amps
- 15 lb weight: 203 ft/min at 8 amps
Telescoping 60” Stainless Boom
The 1 1/4” diameter marine-grade stainless steel boom extends to 60” to carry your cable clear of the transom, the motor and your other lines. When the day is done, it slides back to 36” so the downrigger is out of the way at the dock and on the trailer. That reach makes the 1106 a natural fit for bigger boats.
Hands-Free Auto-Stop and Jog Control
Flip the switch and the 1106 retrieves the weight and stops automatically at the surface. Thread the included auto-stop beads onto the cable and it will stop at any preset depth instead, which makes stacking lines and resetting to a hot depth effortless. A separate jog button gives you fine control over the weight’s position.
Clutch Brake with Adjustable Descent
Scotty’s clutch brake lets you send the weight down at whatever speed you choose: a slow, even drop to prevent tangles, or a fast plunge when you need a lure deep right now. It is factory set to pay out cable if the weight hangs up on the bottom, which helps protect the downrigger, the cable and your boat.
Spray-Protected Depth Counter
The positive-drive mechanical counter reads directly from the spool and is protected from spray. Note the reading when a rod fires, and you can put every line straight back into the strike zone.
Kevlar Drive Belt by Optibelt
Power reaches the spool through a Kevlar-reinforced drive belt made by Optibelt™, for smooth, quiet, efficient operation trip after trip.
Rod Master II Rod Holder
The boom-mounted, adjustable No. 358 Rod Master II holds your rod right above the downrigger, where you can watch the tip load and get to the rod fast the moment a fish trips the release.
16-Position Swivel Base and Tilt-Up Bracket
The included No. 1026 swivel pedestal mount turns a full 360° and locks into 16 positions, so you can swing the boom out to troll and back inboard to land fish or service the rig. The No. 1023 tilt-up bracket lets you stand the downrigger upright and lock it for docking, washdowns and trailering.
Plug-In 12V Power
A Scotty/Marinco® 12V plug and receptacle, with a right-angle receptacle mount, turn installation into plug-and-play. Pull the plug to remove the downrigger and the receptacle stays neatly on the boat.
Built for Fresh and Salt Water
Scotty has built downriggers in Canada for more than 50 years. The 1106 arrives fully assembled, factory and field tested, with complete saltwater protection for the Great Lakes, inland lakes and coastal waters.
Is the 1106 Right for Your Boat?
Scotty designs its Depthpower downriggers for wide-beam boats of 16 ft and longer, and recommends mounting them near the stern to keep the cable away from the prop. It is ideal for salmon, lake trout, walleye and other species that hold at a specific depth. Scotty recommends 12–15 lb weights for most conditions.
1106 or 1106B? — The 1106 runs 150 lb stainless steel cable, the traditional choice for durability and a proven setup. The 1106B is the same downrigger spooled with low-drag braided line, which cuts through the water with less blowback.
Installation Checklist
- 12V battery connection run with marine-grade 10-gauge wire
- Inline 30 A fuse within 7” of the battery (Scotty No. 1124, sold separately)
- Wood or metal backing plate under the mount to spread the load
- Rear edge of the bracket within 1/4” of the inside edge of the gunwale
- Downrigger weight of 12–15 lb for most conditions
Care and Maintenance
- Rinse the downrigger and cable with fresh water after every trip, especially in salt water.
- Keep the plug contacts clean and free of corrosion.
- Do not lubricate the unit; lubricants can damage the plastic parts and affect the brake.
- Never use monofilament or nylon as downrigger line.
- Limit long-term sun exposure; Scotty’s No. 3015 cover is available separately.
What’s Included
- Scotty 1106 Depthpower electric downrigger with 36”–60” telescoping boom
- 250 ft of 150 lb test stainless steel cable, pre-spooled
- No. 358 Rod Master II rod holder
- No. 1170 Power Grip Plus 18” line release
- No. 1121 auto-stop with 4 auto-stop beads
- No. 1026 swivel pedestal mount
- No. 1023 tilt-up mounting bracket
- No. 2128 right-angle receptacle mount
- Scotty/Marinco 12V plug and receptacle
Buying and Setup Notes
Before installing, check mounting-surface strength, clearance and compatibility with your boat's existing rod holders or tracks. Consider boom reach, the supplied cable or braid, trolling-weight rating and whether the rod-holder arrangement fits your fishing style. Keep hands clear of the working line while retrieving weights. Follow the manufacturer's fastener and operating guidance.
| Brand | Scotty |
| Model | 1106 |
| Series | Depthpower |
| Type | Electric Downrigger |
| Boom Length | 36”–60” Telescoping |
| Boom Diameter | 1 1/4” |
| Boom Material | Marine-Grade Stainless Steel |
| Downrigger Cable | 250 ft, 150 lb Test Stainless Steel |
| Retrieval Speed | 235 ft/min (7 lb) / 222 ft/min (10 lb) / 203 ft/min (15 lb) |
| Amperage Draw | 4 A (7 lb) / 5 A (10 lb) / 8 A (15 lb) |
| Recommended Weight | 12–15 lb |
| Drive | Positive-Drive Kevlar Belt by Optibelt |
| Brake | Clutch Brake, Adjustable Descent |
| Counter | No. 1145 Mechanical, Spray-Protected |
| Auto-Stop | No. 1121, Multi-Position, with Jog Button |
| Rod Holder | No. 358 Rod Master II, 1.85” Inside Diameter |
| Line Release | No. 1170 Power Grip Plus 18” |
| Mounts | No. 1026 Swivel (360°, 16 Positions), No. 1023 Tilt-Up, No. 2128 Receptacle |
| Power | 12V DC, Scotty/Marinco Plug & Receptacle, 40” Cord |
| Fuse Required | 30 A Inline (Not Included) |
| Recommended Boat | Wide-Beam, 16 ft and Longer |
| Weight | 23.2 lb |
| UPC | 062017111063 |
| Water | Freshwater & Saltwater |
| Made In | Canada |
| Warranty | Limited Lifetime (Original Purchaser) |
| Brand | Scotty |
| Model | 1106 |
| Series | Depthpower |
| Type | Electric Downrigger |
| Boom Length | 36”–60” Telescoping |
| Boom Diameter | 1 1/4” |
| Boom Material | Marine-Grade Stainless Steel |
| Downrigger Cable | 250 ft, 150 lb Test Stainless Steel |
| Retrieval Speed | 235 ft/min (7 lb) / 222 ft/min (10 lb) / 203 ft/min (15 lb) |
| Amperage Draw | 4 A (7 lb) / 5 A (10 lb) / 8 A (15 lb) |
| Recommended Weight | 12–15 lb |
| Drive | Positive-Drive Kevlar Belt by Optibelt |
| Brake | Clutch Brake, Adjustable Descent |
| Counter | No. 1145 Mechanical, Spray-Protected |
| Auto-Stop | No. 1121, Multi-Position, with Jog Button |
| Rod Holder | No. 358 Rod Master II, 1.85” Inside Diameter |
| Line Release | No. 1170 Power Grip Plus 18” |
| Mounts | No. 1026 Swivel (360°, 16 Positions), No. 1023 Tilt-Up, No. 2128 Receptacle |
| Power | 12V DC, Scotty/Marinco Plug & Receptacle, 40” Cord |
| Fuse Required | 30 A Inline (Not Included) |
| Recommended Boat | Wide-Beam, 16 ft and Longer |
| Weight | 23.2 lb |
| UPC | 062017111063 |
| Water | Freshwater & Saltwater |
| Made In | Canada |
| Warranty | Limited Lifetime (Original Purchaser) |